Density and Concentration Measurement DIMF Bopp & Reuther
Density and Concentration Measurement DIMF Bopp & Reuther

Density and Concentration Meter DIMF

The liquid density meter of the DIMF series is used for continuous measurement of the density/concentration of liquids or liquid mixtures. The proven tuning fork principle guarantees a high acccuracy with very good long term stability.The robust design ensures reliable operation even under harsh operating conditions. pdf datasheet

Filling and Dosing Solutions Bopp & Reuther
OKTronic Dosing Metering Skid Solutions Bopp & Reuther

Dosing and Filling Stations

Dosing and Filling Stations for oil and water based media - Palm Oil, Oils & Fuels and waterbased beverages, pharmaceutical and chemical liquids pdf datasheet

Dosing and Filling Solutions Bopp & Reuther
Dosing and Filling Solutions Bopp & Reuther

Oil Dosing Meter OKTronic

The electro-pneumatic dosing meter OKtronic combines the precise metering of approved oval wheel meter, the intelligent elektronic and modern valve technology to a robust and universal applicable metering unit. pdf datasheet

Metering Skid Solutions Bopp & Reuther
Metering Skid Solutions Bopp & Reuther

Metering Skid Solutions

Metering Skid Solutions for Batch Measurement: Loading / Unloading, Continuous Measurement: Pipeline Blending and Additive Injection Units Dosing pdf datasheet

Centrifugal Gas Separator Bopp & Reuther

Centrifugal Gas Separator

Centrifugal Air Separators are used to avoid measuring errors that result from air or gas contained in liquids measured with volumetric and mass flow meters. pdf datasheet

Strainer, Filter Bopp & Reuther

Strainer

Strainers are used to avoid measuring errors and damage caused by solid particles contained in the fluid. pdf datasheet

Universal Flowcomputer UR6, URS6, URS9  Bopp & Reuther
Spiramag Electro-Magnetic Flowmeter Bopp & Reuther

Universal Flow Computer UR-URS

The flow computers are used to record, display and output mass and volume flows, including the calculation of net values for standard conditions. pdf datasheet

Spiramag Electro-Magnetic Flowmeter Bopp & Reuther

Electromagnetic Flowmeter Spiramag

General purpose magnetic inductive flowmeter for applications in the water / waste water industry pdf datasheet

Oriflow Compact Orifice Flowmeter Bopp & Reuther
Turbine Flowmeter RQ Bopp & Reuther

Compact Orifice Oriflow

The compact orifice Oriflow for flow measurements of conductive and non-conductive fluids, gases and vapours, volume/mass measurement pdf datasheet

Turbine Flowmeter RQ Bopp & Reuther
PD Flowmeter Oval Gear OD Bopp & Reuther

Turbine Flowmeter RQ

The Turbine Flowmeter RQ Measuring liquids and liquefied gases in the chemical and petrochemical industry, in the mineral oil industry and loading systems, especially for high operating pressures and low viscosities, 0.15 to 2,400 m³/h, accuracy up to ±0,15% pdf datasheet

Turbine Flowmeter RQ Bopp & Reuther

Oval Wheel Flowmeter OD

This meter is designed for the measurement non-conductive liquids, e.g. oil or demineralized water. An inlet or outlet section is not required., 0.2 -100 l/min, accuracy up to ±0,25% pdf datasheet

PD Flowmeter Oval Gear Flowal Plus Bopp & Reuther

Oval Wheel Flowal Plus

The Flowal Plus is a versatile flowmeter for measuring the volume of liquids in mechanical engineering, factory automation and process instrumentation combined with modern electronics. It is suited for industrial fluids, chemical fluids, mineral oils and fuels. , 0.03 -600 l/min, accuracy up to ±0,25% pdf datasheet

PD Flowmeter Oval Gear Flowal Plus Bopp & Reuther

Oval Wheel Flowmeter OK

Oval wheel meters type OK are used for dosing of liquid chemical fluids such as solvents, resins, paints and varnishes, alkalis, organic and inorganic acids, depending on temperature and concentration., 0.2 -1,200 l/min, accuracy up to ±0,1% pdf datasheet

PD Flowmeter Oval Gear OI Bopp & Reuther

Oval Wheel Flowmeter OI

Oval wheel meters type OI are used for the measurement of liquid products such as liquefied gases, acids, alkaline solutions, fats, alcohols, solvents, dispersions, polymers, poly-condensates, paints, colors and adhesives, 0.2 -1,200 l/min, accuracy up to ±0,1% pdf datasheet

PD Flowmeter Oval Gear OP Bopp & Reuther

Oval Wheel Flowmeter OP

Oval wheel meters type OP are used for measuring liquids such as gasolines, heating/lubricating/diesel oil, bio ethanol, chemical liquids, 0.08-5,000 l/min, accuracy up to ±0,2% pdf datasheet

PD Flowmeter Oval Gear OAP Bopp & Reuther

Oval Wheel Flowmeter OAP

The Premium Oval Wheel Meter Type OaP for liquid raw, intermediate and finished hydrocarbon and chemical liquids: double case, custody transfer, SIL2 certified, 5 -24,000 l/min, accuracy up to ±0,05% pdf datasheet

lpt336

Pressure Transmitter for H2 and technical gases

The industrial pressure transmitter LPT 336 with a welded stainless steel sensor for hydrogen, oxygen and other technical gas applications pdf datasheet

Leitenberger Calibration barometric air pressure handheld device xa1000 series for airpressure, humidity, temperature

Handheld for barometric pressure, temperature, humidity and airflow

High accurate handheld for Barometric Air Pressure, Range: 800...1100 mbar absolute, Touch-Screen, battery operated, data logging, PC software "SmartGraph3" download pdf datasheet

Leitenberger LR LTS-350 IO-link temperature switch

Temperature Switch LTS 300 IO-Link

The electronic temperature switch LTS 300-IO with an IO-Link interface as standard in order to exchange process data, system monitoring, diagnostic reports and status messages with a superordinate control level, from -40°C to 150°C pdf datasheet

Leitenberger mechanical Bourdon Tube diaphragm pressure switch 03.30 for vacuum and compound pressure

Diaphragm Pressure Switch - Bourdon Tube - vacuum to 600 bar

The mechanical Bourdon Tube pressure switch for rough working conditions with aggressive fluids or high temperature. Range: vacuum and compound pressure up to 600 bar pdf datasheet

Leitenberger mechanical diaphragm pressure switch 03-27, 03-40 for vacuum and compound pressure

Diaphragm Pressure Switch for compound and vacuum pressure

The mechanical diaphragm pressure switch with for vacuum and compound pressure upto 160 bar pdf datasheet 03.40 pdf datasheet 03.27

Leitenberger mechanical diaphragm pressure switch 03-10 for vacuum and low pressure

Diaphragm Pressure Switch 03.10 for low and vacuum pressure

The mechanical diaphragm pressure switch with ranges from 0...1 bar to 0...25 bar and vacuum pdf datasheet

Leitenberger electronic pressure switch DS4 or low and vacuum pressure, compact

Pressure Switch DS4 low/vacuum compact

The DS4 electronic pressure switch for Silizium sensor for pneumatic applications. Pressure ranges 0...10 mbar to 0...1 bar and vacuum -1...0 bar pdf datasheet

Leitenberger electronic pressure switch DS-P flush welded, Exia, intrinsically safe, flush welded

Pressure Switch DS-P flush welded, Exia

The electronic DS-P pressure switch Stainless steel diaphragm, flush, for hygienic, paint, chemical, high viscosity applications pdf datasheet DS200P pdf datasheet DS400P

Leitenberger electronic pressure switch DS214 for high pressure

Pressure Switch DS214 high pressure

The electronic DS214 high pressure switch with pressure ranges from 0...600 bar to 0...2200 bar pdf datasheet

Leitenberger electronic pressure switch DS210 for low and vacuum pressure

Electronic Pressure Switch DS210 low/vacuum pressure

The electronic DS210 low and vacuum pressure switch. Pressure ranges 0...10 mbar to 0...1 bar and vacuum -1...0 bar pdf datasheet

Leitenberger electronic pressure switch DS201, DS401, DS230 with ceramic sensor, intrinsically safe

Pressure Switch DS ceramic sensor, Exia

The electronic DS pressure switch with ceramic sensor, intrinsically safe for gases (Exia), Pressure ranges up to 600 bar pdf datasheet DS401 pdf datasheet DS201 pdf datasheet DS230

Leitenberger electronic pressure switch DS 200, 202, 400 universal

Electronic Pressure Switch DS universal, ss sensor, Exia

The electronic universal DS pressure switch with stainless steel sensor, intrinsically safe for gases (Exia), Pressure ranges from 0...100 mbar to 0...600 bar pdf datasheet DS400 pdf datasheet DS200 pdf datasheet DS202

Leitenberger electronic pressure switch LDS 350-io IO-Link

Pressure Switch LDS 350 IO-Link 600 bar

The electronic pressure switch LDS 350-IO with an integrated IO-Link interface to exchange process data, diagnostic reports and status messages and control the process application. Pressure ranges from 0 ... 100 mbar up to 0 ... 600 bar pdf datasheet

Leitenberger ultra high Pressure Transmitter DMP 304 up to 6000 bar

Ultra High Pressure Transmitter DMP 304 up to 6000 bar Exia for gases

The ultra-high-pressure transmitter type DMP 304 with rugged stainless steel housing for applications with highest demand on precision and reliability. DMP 304 series is based on a compensated strain gauge, bonded onto a stainless steel diaphragm - adjustable ranges from 0...2000 bar to 0...6000 bar, accuracy 0.5% FS (opt 0. 25%FS) pdf datasheet

Leitenberger Precision Pressure Transmitter DMP 334i up to 2200 bar

Precision Pressure Transmitter DMP 334i up to 2200 bar

Precision Pressure Transmitter DMP 334i, adjustable ranges from 0...600 bar to 0...2200 bar, accuracy 0.1% FS pdf datasheet

Leitenberger Precision Pressure Transmitter DMP 331i, DMP 333i Exia intrinsically safe

Precision Pressure Transmitter DMP 331/333i Exia

Precision Pressure Transmitter, adjustable ranges from 0...400 mbar to 0...600 bar, accuracy 0.1% FS, intrinsically safe Exia option pdf datasheet

Leitenberger Pressure Transmitter LPT 533 IO-Link

Pressure Transmitter LPT 533 IO-Link

Pressure Transmitter LPT533 with IO-Link interface, adjustable ranges from 0...100 mbar to 0...400 bar, accuracy 0.35% FS (opt 0.25%FS) pdf datasheet

Leitenberger Calibration digital pressure gauge DM80, DM80-UMS, DM80-S

Digital Pressure Gauge DM80

The digital pressure gauges DM 80, DM 80-UMS, DM 80-S are used for inidcation of measured pressure values, for testing and diagnose purposes in hydraulic applications download pdf datasheet

Leitenberger pneumatic vacuum pressure test pump model LR-Cal 2941 for calibration

Pneumatic Vacuum Pressure Test Pump LR-Cal 2941

The vacuum test pump LR-Cal 2941 is used to generate vacuum (negative pressure down to -0.9 bar) for checking, adjusting and calibrating mechanical and electronic pressure measuring instruments by comparative measurements. download pdf datasheet

Leitenberger pneumatic low pressure test pump model LR-Cal 2911 for calibration

Pneumatic Low Pressure Test Pump LR-Cal 2911

The pressure test pump LR-Cal 2911 is used to generate pressure up to 7 bar for checking, adjusting and calibrating mechanical and electronic pressure measuring instruments by comparative measurements download pdf datasheet

Leitenberger pneumatic low pressure and vacuum test pump model LR-Cal LPP 08 for calibration

Pneumatic Pressure Test Pump LR-Cal LPP 08

Manually pressure and vacuum generation (-0,85...+8 bar) for checking, adjusting and calibrating mechanical and electronic pressure measuring instruments by comparative measurements in the low-pressure and vacuum range. download pdf datasheet

Leitenberger Calibration Hydraulic Pressure Calibration Deadweight Tester LR-Cal LDW-HK

Hydraulic Deadweight Tester compact LDW-HK

Complete Stand-alone Deadweight Tester / Pressure Balance LR-Cal LDW-HK Deadweight Tester / Pressure Balance, LR-Cal LDW-HK Hydraulic, max. 1200 bar download pdf datasheet

Leitenberger Calibration Hydraulic Pressure Calibration Deadweight Tester LR-Cal LDW-H

Hydraulic Deadweight Tester high accuracy LDW-H

High Accuracy, Stand-alone Deadweight Tester / Pressure Balance LR-Cal LDW-H, Hydraulic, max. 1400 bar download pdf datasheet

Leitenberger Calibration Differential Pressure Calibration Deadweight Tester LR-Cal CPB5000-DP

Hydraulic Deadweight Tester high pressure CPB5000-HP

High Pressure, Stand-alone Deadweight Tester / Pressure Balance LR-Cal CBP5000-HP, Hydraulic, max. 5000 bar download pdf datasheet

Leitenberger Calibration Differential Pressure Calibration Deadweight Tester LR-Cal CPB5000-DP

Hydraulic Deadweight Tester differential pressure CPB5000-DP

Differential Pressure, Stand-alone Deadweight Tester / Pressure Balance LR-Cal CBP5000-DP download pdf datasheet

Leitenberger Calibration Pneumatic Pressure Calibration Deadweight Tester LR-Cal LDW-P

Pneumatic Deadweight Tester LDW-P

Stand-alone Deadweight Tester / Pressure Balance LR-Cal LDW-P, Pneumatic, max. 100 bar download pdf datasheet

Leitenberger pneumatic pressure test pump model LR-Cal LPP 40 for calibration

Pneumatic Pressure Test Pump LR-Cal LPP 40

Manually pressure generation up to 40 bar, switchable to manually vacuum generation up to -0.95 bar. Pneumatic, operated with ambient air download pdf datasheet

Leitenberger pneumatic pressure test pump model LR-Cal LPP 60 for calibration
Leitenberger hydraulic pressure test pump model LR-Cal LPP 700 water and air for calibration

Pneumatic Pressure Test Pump LR-Cal LPP 60

Manually pressure generation up to 60 bar, switchable to manually vacuum generation up to -0.95 bar Pneumatic, operated with ambient air download pdf datasheet

Leitenberger hydraulic pressure test pump model LR-Cal LPP 700 water and air for calibration

Hydraulic Pressure Test Pump LR-Cal LPP 700

Hydraulic Pressure Test Pump Manually pressure generation up to 700 bar (10000 psi) Hydraulic, operated with oil or water download pdf datasheet

Leitenberger calibration pneumatic pressure comparison test pump benchtop model LPP60-T

Pneumatic Pressure Comparison Test Pump Bench Type LR-Cal LPP 60-T

Pressure Comparator, pneumatic hand lever pump - bench type. Pressure generation up to +60 bar, switchable to Vacuum generation up to -0.95 bar. Medium: ambient air. download pdf datasheet

Leitenberger hydraulic pressure test pump model LR-Cal LPP 1000 water and air for calibration

Hydraulic Pressure Test Pump LR-Cal LPP 1000

Hydraulic Pressure Test Pump Manually pressure generation up to 1000 bar (14500 psi) Hydraulic, operated with oil or water (optional with SKYDROL®) download pdf datasheet

Leitenberger pneumatic pressure comparison test pump benchtop model LSP100-T benchtop pump

Pneumatic Pressure Comparison Test Pump Bench Type LR-Cal LSP 100-P

Pressure Comparator, pneumatic hand lever pump. Pressure generation up to +100 bar, switchable to Vaccum generation up to -0.95 bar. Medium: ambient air. download pdf datasheet

Leitenberger Calibration Electronic Pressure Calibrator LPC200
Leitenberger calibration hydraulic pressure comparator spindle pump LSP1000-H, LSP1200H, LSP1600-H

Hydraulic Pressure Compariator Test Pump upto 1600 bar

Pressure Comparator, hydraulic spindle pump. Pressure generation up to 1600 bar. With rigid base plate. Medium: mineral oil or water. download pdf datasheet

Leitenberger calibration hydraulic high pressure comparator spindle pump LSP4000-H, LSP7000H
Leitenberger calibration hydraulic high pressure comparator spindle pump LSP4000-H, LSP7000H

Hydraulic Pressure Comparison Test Pump upto 7000 bar

Pressure Comparator, hydraulic spindle pump. Pressure generation up to 7000 bar. With rigid table housing. download pdf datasheet

Leitenberger Calibration Electronic Pressure Calibrator LPC200
Leitenberger Calibration Electronic Pressure and Documenting Process Calibrator LPC300

Electronic Pressure and Documenting Process Calibrator LPC300

The electronic pressure and process documentation calibrator LR-Cal LPC 300 is used for high precision calibration of pressure instruments, e.g. pressure gauges, pressure transmitter, digital manometer, pressure switches, overpressure protection valves, etc. - up to 6000 bar download pdf datasheet

Leitenberger Calibration Electronic Pressure and Temperature Calibrator LPC200-T

Electronic Pressure and Temperature Calibrator LPC200-T

Electronic Pressure & Temperature Calibrator upto 6000 bar, and vacuum, compound and absolute pressure ranges, high accuracy, exchangeable reference pressure sensors. chargeable Li-Ion battery download pdf datasheet

Leitenberger Calibration Electronic Pressure Calibrator LPC200

Electronic Pressure Calibrator LPC200

Electronic Pressure Calibrator upto 6000 bar, and vacuum, compound and absolute pressure ranges, high accuracy, exchangeable reference pressure sensors. chargeable Li-Ion battery download pdf datasheet

Leitenberger Calibration Digital reference pressure gauge LDM70

Digital reference pressure gauge LDM 80

Digital Precision reference pressure gauge, Pressure range 0-100mb, 0-3000 bar, datalogging, bar graph, medium temperature, USB interface, chargeable battery, opt. wireless and pressure switch test download pdf datasheet

Leitenberger Calibration Digital reference pressure gauge LDM70

Digital reference pressure gauge LDM 70

Digital reference pressure gauge, Pressure ranges: from 0...0.1 bar to 0...600 bar, and vacuum, compound and absolute pressure ranges, battery operated. download pdf datasheet

Leitenberger Calibration LHM handheld Indicator for pressure, force, torque, internal and external sensor

handheld indicator LHM for low pressure, force, weight, torque

Professional handheld indicator LHR-Cal LHM for vacuum/low pressure (up to 5 bar), force/weight and torque,with internal and up to 7 external pressure and force sensors, automatic recognition, data logger,USB interface, PEAK function, linearization, wireless option download pdf datasheet

Leitenberger Calibration Pressure Controller Model LR-Cal LCC 100 for small pressure, vacuum and differential pressure ranges

Handheld Digital Manometer Series 2000

The digital handheld manometer LR-Cal Series 2000 for the precise measurement of 25 mbar to 10 bar pressure, vacuum, DP measurement of non-corrosive and non-ionic fluids and gases, e.g. air, clean gases and hydraulic fluids. download pdf datasheet

Leitenberger Calibration Pressure Controller Model LR-Cal LCC 100 for small pressure, vacuum and differential pressure ranges

Pneumatic Pressure Controller for Gauge and Vacuum

Air operated pressure controller LCC100 (no external source required) for pressure up to 2000 mbar, DP, Vacuum down to -650 mbar download pdf datasheet

Leitenberger Pressure & Temperature Calibration Testkits LR Cal LPP-kit DNV-GL for ships and marine vessels
Leitenberger Pressure Calibration Testkits LR Cal LPP-kit

Marine Vessel Calibration Testkits

Pressure Calibration Kits LR-Cal LPP-KIT, Pressure source (test pump) and reference pressure gauge / calibrator in portable case, DNV-GL marine certification.. download pdf datasheet

Leitenberger Pressure Calibration Testkits LR Cal LPP-kit

Digital Pressure Calibration Kits LPP

Pressure Calibration Kits LR-Cal LPP-KIT, Pressure source (test pump) and reference pressure gauge / calibrator in portable case. download pdf datasheet

Leitenberger Calibration digital pressure gauge kit with pump DM80
Leitenberger Calibration digital pressure gauge kit with pump DM80

Digital Pressure Gauge Testkit with Pump DM80

TESTKIT in transit case with Pressure test pump, digital pressure gauges, NPT, BSP, metric threaded adapters, incl. factory calibration certificate download pdf datasheet

Leitenberger Calibration Working Hydraulic Diagnostic Testkit HPKD-AH for commercial vehicles, tractors, trucks

Hydraulic Diagnostic Testkit HPKD-AH

Working hydraulics Test Kit for commercial vehicles, tractors, trucks, etc. with 2 digital pressure gauges to enables quick and reliable diagnostics of all kind of working hydraulic systems. download pdf datasheet

Leitenberger calibration hydraulic diagnostic testkit HPKD, HPK, HPKD-UMS to enable quick and reliable diagnostics of all kind of hydraulic systems

Hydraulic Diagnostic Testkit HPK

Hydraulic Test Kits digital or analogue reference pressure gauges, hoses and adapters to enable quick and reliable diagnostics of all kind of hydraulic systems download pdf datasheet

Leitenberger calibration hydraulic diagnostic device LR-Cal HD01

Hydraulic Diagnostic Device HD01

Hydraulic diagnostic device with 2 Channels to measure and display pressure, flow and temperature diagnostics in hydraulic systems download pdf datasheet

DFP Leitenberger digital force pressure gauge
DFP Leitenberger digital force pressure gauge

Torque and Force Meter for Benches LFC80

Digital Torque Meter for benches optional with mechanical support with dual linear guide for calibration of torque wrenches download pdf datasheet

The multifunctional Temperature Calibrator LR-Cal  LTC 100 is a high-precision, hand-held calibrator for the calibration and troubleshooting of process control instrumentation.

Handheld Portable Temperature Calibrator LTC100

Handheld temperature calibrator to measure and simulate thermocouples, resistance thermometers, current, voltage and resistance, Data logging on supplied SD card, powered by chargeable Li-ion battery download pdf datasheet

DFP Leitenberger digital force pressure gauge

Reference Pressure and Force Gauge DFP

Digital Reference Pressure Gauge, scalable conversion to force & weight, perfect for checking pressure gauges at hydraulic presses, force and weight conversion download pdf datasheet

Leitenberger Calibration Portable loop powered Multifunction Temperatur Calibrator Model LR-Cal LLC 100

Handheld Portable Temperature Loop Calibrator LLC100

The portable handheld calibrator LR-Cal LLC 100 is a Milli amp loop powered instruments, which it can measure, source and simulate. Sourcing can be increment, step, ramp or valve stroking. DC voltage and circuit continuity can be measured. download pdf datasheet

Leitenberger Calibration Precision Reference Thermometer Model LR-Cal LRT 1000

Precision Reference Thermometer LR-Cal LRT 1000

The reference thermometer LR-Cal LRT 750 is a comparison reference for checking The Precision Reference Thermometer Model LR-Cal LRT 1000 is a very high accurate reference for comparison temperature measurements. download pdf datasheet

Leitenberger Calibration Reference Thermometer Model LR-Cal LRT 750

Precision Reference Thermometer LR-Cal LRT 750

The reference thermometer LR-Cal LRT 750 is a comparison reference for checking and calibrating all kind of thermometer. The system consists of a battery powered digital handheld indicator and a pre-aged precision sensor with temperature range -200...+450°C. download pdf datasheet

Leitenberger Dry Block Calibrator portable LR-Cal Quarz, Pulsar, Solar, Pyros

Dry Block Calibrator portable

Portable dry well (block) temperature calibrators for controlled temperature calibration.Models range from -50°C to +1200°C - software calibration options for cal procedure and certification. download pdf datasheet

pyros-bb

Dry Block Calibrator for Infrared Cal.

Dry Block Temperature Calibrator with Black Body LR-Cal PYROS-BB, range +24°C...+650°C, with Black Body insert for of non-contact infrared thermometer calibration download pdf datasheet

Leitenberger Fluid and LTC Calibration Micro Bath for temperature calibration

Temperature Calibration Micro Bath

Temperature Calibration Micro Bath with high accuracy and stability for different fluids, touch screen option, -40°C to +300°C download pdf datasheet

Aplisens Pitot Tube Flow Sensor PRP
Aplisens PEM-1000ALW, PEM-1000NW Electromagnetic flowmeter

Pitot Tube Flow Sensor PRP

The PRP Pitot Tube Flowsensor measures the flow in pipes and ducts according to the differential pressure working principle. It allows bidirectional flow with low pressure loss, low maintenance and installation cost and accurate long term reading. pdf datasheet

KAP-03 HART Field communicator is a portable and battery powered device specifically designed for communicating with Aplisens SMART transmitters, explosion proof option

Handheld HART Communicator

KAP-03 HART Field communicator is a portable and battery powered device specifically designed for communicating with Aplisens SMART transmitters, explosion proof option download PDF Hart Communication Tools

Mobile Configurator for Android based devices to communicate and transfer data with Aplisens transmitters.

Aplisens Android Mobile Configurator

Mobile Configurator for Android based devices to communicate and transfer data with Aplisens transmitters. download PDF Hart Communication Tools

The  program  Raport  2  was  designed  for  communication  and  data  exchange  with  intelligent devices (pressure and temperature transmitters, etc.) produced by Aplisens.

Raport 2 - HART and Modbus PC software

The advanced HART communication software Raport 2 to configure, monitor and record your HART and MODBUS instruments from Aplisens download PDF Hart Communication Tools

HART Modem USB & Wireless Bluetooth HART Modem for PC and Mobile devices Aplisens

USB & Wireless Bluetooth HART Modem for PC and Mobile devices

HART/USB converter allows for connecting and configuration of Hart transmitters via USB port. It works also with devices equipped in Bluetooth. download PDF Hart Communication Tools

efco-autoPSH909
PSH1067

Horizontal Test Benches customized

Individual horizontal test benches for clamping shut-off and control valves, customizable, clamping force: 7,5t-1500t - Range: DN 15 to DN 1000 pdf Testbench

kep Thermal and Impact Printers, Panel Mount Printers for Panel Meters

Printer Accessories

Thermal and Impact Printers, Panel Mount Printers for Panel Meters pdf datasheet

KEP Process Indicator ml-P18 with universal input

Process Indicator ml-P18 with universal input

The mL-PI8 process indicators are designed for measuring temperature and any process value. They can be used in many applications with their universal process input Process Indicator – Universal Input (TC, RTD, mV DC, V DC, mA DC), alarm functions and serial communication unit.

KEP Intellect 69 INT Rate Totalizer with analog input

Intellect 69 INT Rate Totalizer with analog input

The Intellect-69 is an integrating totalizer & ratemeter which accepts analog signal inputs. The unit can be field programmed to accept 4-20mA, 0-20mA, 0-5V, 0-10V or 1- 5V signals

kep MINITrol MRT Rate Totalizer with pulse input

MINITrol MRT Rate Totalizer with pulse input

The MINItrol (MRT) is a 6 digit totalizer and ratemeter with two level, 5 digit preset alarm control of total or rate.

Hycontrol Rotary Paddle Level Switch RP series for solids

Rotary Paddle Switches RP

The Rotary Level Switch RP series is excellent for solid products such as cement, sand and plastic pellets. The Hycontrol range is available with various extension lengths and paddle shape options.

The Aplisens WW-11N indicator display can be used with any device having the output signal of 4...20 mA. The WW-11N has a configurable display range from –999 to 9999.

Digital Pressure Indicator WW-11N

The WW-11N display can be used with any device having the output signal of 4...20 mA. The WW-11N has a configurable display range from –999 to 9999. Either linear or radical characteristic may be selected as well as display filtering level and rounding of the reading number. pdf datasheet

The Aplisens WW-45 indicator is used with any device with a 4-20mA output signal to give an additional 4 digit LED display of absolute or relative pressure measurement - double circuit line with no auxiliary power supply needed.

Digital Pressure Indicator WW-45

The WW-45 indicator is used with any device with a 4-20mA output signal to give an additional 4 digit LED display of absolute or relative pressure measurement - double circuit line with no auxiliary power supply needed. pdf datasheet

KEP Battery/Loop powered Flow Rate & Total with Alarm BATRTM3SS

Battery/Loop powered Flow Rate & Total with Alarm

Featuring 4.5 digits of rate and 8 digits of total, the BAT RAT-M is a battery powered indicator with flow rate alarm output. It is capable of accepting magnetic pickup, DC pulse and switch closure inputs. The unit can be ordered with an optional 4-20mA output. The BAT RAT-M uses the 4-20mA loop to provide power when this output is used. pdf datasheet

Battery/Loop powered Flow Totalizer/Ratemaker BATRTM2

Battery/Loop powered Flow Totalizer/Ratemaker

Featuring 5 digits of rate and 8 digits of total, the BAT R/T Millennium edition is a battery powered or loop powered indicator capable of accepting magnetic pickup, DC pulse and switch closure inputs from pulse producing flowmeters. The unit can be ordered with an optional 4-20mA output. The BATRT-M uses the 4-20mA loop to provide power when this output is used. pdf datasheet

Battery powered Dual Totalizer KEP BATRTM3NE

Battery powered Dual Totalizer

Featuring 5 digits of resetable total and 8 digits of grand total, the BAT D/T Millennium is a battery powered indicator capable of accepting magnetic pickup, DC pulse and switch closure inputs from pulse producing flowmeters. A scaled pulse output is standard. A 4-20mA loop and/or linearization is optional. pdf datasheet

kep HUMIDITY & TEMPERATURE CONTROLLER

HUMIDITY & TEMPERATURE CONTROLLER

The mL-HTC Temperature + Humidity controller is designed for the control of humidity and temperature in industrial processes. PID or On / Off control is available to control the process. 4 Relays are offered for control and alarm outputs. They are mainly used in glass, plastic, petro-chemistry, textile, automotive and machine production industries. pdf datasheet

PD Flowmeter Oval Gear OAP Bopp & Reuther

PD Flowmeter Trigear

The Trigear PD Flowmeter outperforms its competitors when it comes to the accurate metering of the majority of clean fluids including fuels, oils, additives, chemicals, food bases, paints, viscous emulsions, insecticides, alcohols and solvents whether they be pumped or gravity fed. pdf datasheet

Hycontrol Shield lite Silo Protection System from over pressure

Shield lite Silo Protection System

The Shield Lite compact panel monitoring and control equipment from Hycontrol gives users a range of new monitoring and diagnostic tools and indicating when the system is suffering from blocked filtration or endangered by poor delivery driver behaviour. It is simple to install, can be retro-fitted to existing tank silos and is easy to operate. pdf datasheet

mL-OTC2

TEMPERATURE CONTROLLER ON / OFF WITH 2 RELAYS

The mL-OTC2 series temperature controllers are designed for measuring and controlling temperature. They can be used in many applications with their TC and RTD temperature measurement input, On/Off control form and heating and cooling selection. They are mainly used in glass, plastic, petro-chemistry, textile, automotive and machine production industries. pdf datasheet

mL-CSA84

8 Channel Analog Scanner with 10 relays

The mL-CS8A series 8 channel analog scanner devices are designed for measuring and logging processes. They can be used in many applications with their 0-20mA, 4-20mA or 0-10VDC process input, alarm outputs, selectable alarm functions, RS-232 / RS-485 communications. Application Fields Glass, Plastic, Petro-Chemistry, Textile, Automotive, Machine production industries. Applications Heating, Baking Ovens, Incubators Storages, Air Conditioning pdf datasheet

kep Temperature Controller mL-TCR4

Temperature Controller mL-TCR4

The mL-TCR4 temperature controllers are designed for measuring and controlling a temperature value in industry. They can be used in many applications with their TC and RTD temperature measurement input, multi-function control outputs, programmable control and alarm functions. They are mainly used in glass, plastic, petrol-chemistry, textile, automotive and machine production industries. Accurate and advanced controlling is performed with selectable ON-OFF, P, PI, PD, PID, Self Tune PID, Auto Tune PID functions. pdf datasheet

kep Enclosure with Instrument Panel Option NEMA 4X/IP65

Enclosure with Instrument Panel Option NEMA 4X/IP65

The MS827 Enclosure is ideal for use in most petrochemical plants, sewage plants, food processing areas, packing plants, electroplating plants, etc. pdf datasheet

MINIrate MR2 Pulse Input Rate Meter

MINIrate MR2 Pulse Input Rate Meter

The MR2 is a 4.5 digit rate meter with two level, 5 digit preset alarm control. It offers a scalable pulse input up to 10kHz max. pdf datasheet

Aplisens Fitting Accessories - Valves Needle Valves - 2 Way Manifolds - Ball Valves - Transmission Tubes - Sockets - Adapters - Brackets

Valve Fitting Accessories

Fitting Accessories - Valves Needle Valves - 2 Way Manifolds - Ball Valves - Transmission Tubes - Sockets - Adapters - Brackets pdf datasheet

5-valve manifolds are used where relative pressure transmitters are installed. They enable essential operations to be performed on the transmitters,such as starting up a transmitter or setting the zero position in conditions of static or atmospheric pres

Valve Manifold 5 Valve - VM5

5-valve manifolds are used where relative pressure transmitters are installed. They enable essential operations to be performed on the transmitters,such as starting up a transmitter or setting the zero position in conditions of static or atmospheric pressure. The five-valve manifold also enables a calibrator to be connected for meteorological testing of the transmitter.The VM-5 has a modern lightweight construction.The high precision of manufacture enables individual valves to be opened and closed easily. pdf datasheet

Aplisens 3-valve manifolds are used where relative pressure transmitters are installed. They enable essential operations to be performed on the transmitters,such as starting up a transmitter or setting the zero position in conditions of static or atmosph

Valve Manifold 3 Valve - VM3

3-valve manifolds are used where relative pressure transmitters are installed. They enable essential operations to be performed on the transmitters,such as starting up a transmitter or setting the zero position in conditions of static or atmospheric pressure. The stainless steel VM-3 has a modern lightweight construction. The high precision of manufacture enables individual valves to be opened and closed easily. pdf datasheet

Aplisens The data logger PMS-110/111 is a compact multichannel controller with a capability to record and display data. It is one of the first industrial devices which integrates advanced control functions (PID, ON/OFF, time & profiles etc.) and logg

Multi-Channel Controler PMS 110R

The data logger PMS-110/111 is a compact multichannel-controller with a capability to record and display data. It is one of the first industrial devices which integrates advanced control functions (PID, ON/OFF, time & profiles etc.) and logging of setpoints, excitations and current state of controlled objects. Based on Linux firmware, is stable and the touch screen makes configuration easy and comfortable and data presentation easily readable. pdf datasheet

The industrial data logger PMS-90R from Aplisens is designed to record and display current values as well as to present technological parameter in the form of graphs

Datalogger PMS 90R

The industrial data logger PMS-90R is designed to record and display current values as well as to present technological parameter in the form of graphs. The device is equipped with1, 4 or 8U/I inputs (0/4-20mA, 0/1-5V, 0/2-10V) or RTD/TC inputs (Pt100, Pt500, Pt1000, TC type K, S, J, T, N,R, B, E), one impulse (digital) input for controlling the recording process and one USB Host port for flash data storage. pdf datasheet

The Aplisens ERH float level switches are used for point level detection of liquids in all type of vessels. Operation without external power, side or top mounting, wide temperature and pressure ranges, various process connections, stainless steel wetted

Level Switch ERH

Float level switches are used for point level detection of liquids in all type of vessels. Operation without external power, side or top mounting, wide temperature and pressure ranges, various process connections, stainless steel wetted parts, Ex version and marine certificates make it a universally applicable level switch. pdf datasheet

Aplisens PCE-28 Pressure transmitter with fixed range up to 25 bar

Pressure Transmitter AS fixed range

The AS pressure transmitter for gases, vapors and liquids, Fixed ranges: 0 ÷ 1; 0 ÷ 2,5; 0 ÷ 6; 0 ÷ 10; 0 ÷ 16; 0 ÷ 25 bar - Accuracy 0.4%, 4-20 mA output pdf datasheet

Hycontrol Admittance Level Switch MD series
Hycontrol Admittance Level Switch MD series

Admittance Switch MD series

The advantage of Admittance technology is that it has the ability to work with a considerable build up on the probe without false switching as it can distinguish between a coating and product level. pdf datasheet

Hycontrol Capacitance Switch ME80 antistatic

Capacitance Switch ME80 antistatic

The ME80 capacitance switch utilises an anti-static probe for applications with high static probability, such as plastic pellets. A high-temperature variant is also available. pdf datasheet

Hycontrol Capacitance Switch ME60 Plate Type

Capacitance Switch ME60 Plate Type

The ME60 is a plate-type variation of the standard capacitance probe, with a shorter insertion length. pdf datasheet

Hycontrol Capacitance Switch ME50 Wire Probe

Capacitance Switch ME50 Wire Probe

The cable-mounted ME50 capacitance probe is designed to be hung from the top of a vessel to provide accurate point-level switching. pdf datasheet

Hycontrol Capacitance Switch ME40 Remote

Capacitance Switch ME40 Remote

The ME40 remote electronics capacitance switch is a practical solution to more difficult applications, for example, those with high levels of vibration that may otherwise upset or damage the sensitive components in the probe head. These issues may be overcome by remote-mounting the sensitive parts. pdf datasheet

Hycontrol Capacitance Switch ME30 Corrosion Proof

Capacitance Switch ME30 Corrosion Proof

The ME30 capacitance probe offers reliable point level switching in corrosive media and atmospheres. Hycontrol’s ME Series capacitance level switches provide simple, accurate and reliable level control for a wide range of applications. They are suitable for use on liquids, solids, slurries, pastes, granules, powders and pellets in high temperature, high pressure and corrosive environments. pdf datasheet

Hycontrol Capacitance Switch ME20 High Temperature

Capacitance Switch ME20 High Temperature

The ME20 is a durable level switch capable of functioning in applications up to 200°C. An 800°C version is also available for extreme applications. pdf datasheet

Hycontrol Capacitance Switch ME10 Standard

Capacitance Switch ME10 Standard

The ME10 Standard makes use of versatile capacitance technology to provide precise and reliable level switching for a wide variety of industrial applications. pdf datasheet

Hycontrol Vibrating Level Switch Liquids TF series

Vibrating Level Switch Liquids TF series

Vibrating level switches utilise a piezoelectric crystal to oscillate a blade at its fundamental frequency (also referred to as the natural resonance). When the blade of the probe comes into contact with the process media the natural frequency of oscillation is dampened; the electronics sense the change in frequency which causes the unit to switch. pdf datasheet

Hycontrol Vibrating Level Switch Solids DP series

Vibrating Level Switch Solids DP series

Vibrating level switches utilise a piezoelectric crystal to oscillate a blade at its fundamental frequency (also referred to as the natural resonance). When the blade of the probe comes into contact with the process media the natural frequency of oscillation is dampened; the electronics sense the change in frequency which causes the unit to switch. pdf datasheet

Hycontrol Smartfoam Sensor

Smartfoam Sensor

The SmartFoam sensor is part of Hycontrol’s foam detection range, designed to detect and control foam in a single unit for basic foam applications. It is simple, robust and cost-effective. Within its head, the SmartFoam has its own built-in transmitter so that foam detection and control are managed without the need for an external controller. This integrated Sensor shows reliability, resilience, and complete immunity to fouling. pdf datasheet

Hycontrol Suresense+ Foam Control System

Suresense+ Foam Control System

The SureSense+ is an advanced wall-mounted foam controller, which connects to up to three sensors mounted in a single or multiple process vessel(s). This multi-probe capability allows for fully independent monitoring and dosing control of up to three tanks from a single controller, offering multi-tank users a significant cost saving. pdf datasheet

kep MINIbatcher MB2 Pulse Input, Flow Batcher

MINIbatcher MB2 Flow Batcher w. pulse input

The MINI-Batcher is a 6 digit LED flow batcher with totalizer and 4.5 digit ratemeter display with two relay outputs for batch control . One output is dedicated to the batch amount (Preset A), the other can be activated for Prewarn or Batch/Grand Total. The MB2 can count up to the preset (reset to 0) or down from the preset (set to preset). Start, Stop and Reset functions can be activated from the front panel or remote inputs. The MINI-batcher is a must have for low cost batching systems. pdf datasheet

kep 2 Channel Manifold Controller & Flow Computer ST1

2 Channel Manifold Controller & Flow Computer ST1

The ST1 flowmeter manifold controller is a special flow instrument intended to accept inputs from two flowmeters, one larger and one smaller, and which also controls the bypass valve. The instrument setup contains the calibration information for both flowmeters as well as the manifold flow rate switch setpoint and hysteresis. pdf datasheet

KEP Multifunction Flowcomputer SUPERtrol II

Multifunction Flowcomputer SUPERtrol II

The SUPERtrol II Flow Computer can be used with a variety of flowmeter types in liquid, gas, steam and heat applications. Multiple flow equations are available in a single instrument with many advanced features. The alphanumeric display offers measured parameters in easy to understand format. Manual access to measurements and display scrolling is supported. pdf datasheet pdf Energy & Utility Measurement

Hycontrol Ultrasonic Level Transmitter  Multiflex

Ultrasonic Level Transmitter Multiflex

The Hycontrol Sonarflex sludge blanket and interface controller is a microprocessor-based transmitter, combined with an appropriate RVS sonar transducer and a cleaning mechanism. It can be programmed via an easy menu-driven keypad or remotely via a PC. It is used to measure the blanket level in primary sedimentation tanks or the RAS Blanket and FLOC/FLUFF layers in secondary and final clarifiers. pdf datasheet

Hycontrol Ultrasonic Level Transmitter  Sonarflex Sludge Blanket Detection

Ultrasonic Level Transmitter Sonarflex Sludge Blanket Detection

The Hycontrol Sonarflex sludge blanket and interface controller is a microprocessor-based transmitter, combined with an appropriate RVS sonar transducer and a cleaning mechanism. It can be programmed via an easy menu-driven keypad or remotely via a PC. It is used to measure the blanket level in primary sedimentation tanks or the RAS Blanket and FLOC/FLUFF layers in secondary and final clarifiers. pdf datasheet

Hycontrol Ultrasonic Level Transmitter Reflex LR

Ultrasonic Level Transmitter Reflex LR

The Reflex LR unit pushes the boundaries of non-contact ultrasonic level measurement. This new range of smart level instruments is capable of measuring distances in excess of 60 metres and is suitable for both solids and liquids. Using new technology developed with low frequencies, this new range is capable of measuring in extremely difficult applications including very dusty and dirty environments where most traditional ultrasonics will fail. pdf datasheet

Hycontrol Ultrasonic Level Transmitter Miniflex LR6

Ultrasonic Level Transmitter Miniflex LR

Miniflex LR, with its wide range of transducers and advanced PULSE window echo tracking technology, is capable of measuring virtually any liquid or solid and can be used in a wide range of industries from water and waste, to chemical and process, to quarry and aggregate. pdf datasheet

Hycontrol Ultrasonic Level Transmitter Microflex LR

Ultrasonic Level Transmitter Microflex LR

Microflex LR pushes the boundaries of non-contact ultrasonic level measurement. This new range of smart level transmitters can measure distances up to 60 metres and is suitable for solids and liquids. Using new technology developed with low frequencies, these transmitters can operate in extreme applications, including very dusty and dirty environments, where most traditional ultrasonic units will fail. pdf datasheet

Hycontrol Ultrasonic Level Transmitter Microflex D

Ultrasonic Level Transmitter Microflex D

The Microflex D from Hycontrol is a compact, non-intrusive, loop-powered ultrasonic level transmitter for continuous measurement of liquids. Microflex D does not compromise on quality and provides effortless and intuitive operation together with easy and flexible mounting. pdf datasheet

Hycontrol Guided Wave Radar TDR Reflex VF7 Liquids, Powders&Granules upto 40m

Guided Wave Radar TDR Reflex VF7 Liquids, Powders&Granules upto 40m

The Reflex VF7 TDR microwave level control transmitter is ideal for the measurement of liquids, powders and granules up to a range of 35 m. The unit is unaffected by pressure, temperature, viscosity, vacuum, foam, dust, changes in dielectric constant or coating of the probe. VF7 can measure virtually any product in either Direct or TBF mode, utilising any one of the seven available probe types. pdf datasheet

Hycontrol Guided Wave Radar TDR Reflex VF4 Liquids&Solids

Guided Wave Radar TDR Reflex VF4 Liquids&Solids

Hycontrol's new Reflex VF04 TDR measuring probe measures liquids and solids up to a maximum range of 24m with an accuracy of +/- 5 mm, making it an ideal choice for a wide variety of applications. The unit is unaffected by pressure, temperature, viscosity, vacuum, foam, dust, coating or changes in dielectric constant, and offers a selection of durable and highly reliable probes. pdf datasheet

Hycontrol Guided Wave Radar TDR Reflex VF2 Liquids, Powders & Granules

Guided Wave Radar TDR Reflex VF2 Liquids, Powders&Granules

The Reflex VF2 Series range of TDR guided microwave products is ideal for the measurement of liquids, powders and granules to a range of 40 metres. Unaffected by pressure, temperature, viscosity, vacuum, foam, dust, changes in dielectric constant or coating of the probe, the VF Series level indicators can measure virtually any product in either Direct, Automatic or TBF mode utilising any one of its seven available probe types. pdf datasheet

Hycontrol non-contact Radar RF Series 80 GHz for Narrow Tank -  Liquid Tanks

Radar RF Series 80 GHz for Narrow Tank - Liquid Tanks

The RF Series is a two-wire 80 GHz FMCW radar level measurement transmitter. This measuring device is designed to suit challenging liquid level applications involving narrow tanks with long nozzles and internal obstructions such as agitators, ladders or heating coils. The minimal beam angle and dead zone make this an optimal choice for continuous, non-contact level measurement in both very small and very high tanks (up to 100 m/328 ft). pdf datasheet

Hycontrol non-contact Radar Transmitter RE Series 24 GHz for Corrosive Liquids

Radar RE Series 24 GHz for Corrosive Liquids

Hycontrol’s RE Series two-wire 24 GHz FMCW radar level transmitter is designed for a broad spectrum of liquid applications, most notably for corrosive liquid products. It measures distance, level and volume of liquids and pastes, and is ideal for measuring the level of corrosive liquids in agitated tanks up to a range of 100 m/328 ft. The unique drop-shaped antenna option is perfectly suited for aggressive liquids, acids and other corrosive substances. pdf datasheet

Hycontrol non-contact Radar Transmitter RB Series 24 GHz for Basic Liquids

Radar RB Series 24 GHz for Basic Liquids

The RB Series two-wire 24 GHz FMCW radar level transmitter has been developed by Hycontrol for basic liquid process applications. The device is particularly appropriate for continuous, non-contact level measurement in the chemical, petrochemical, and oil and gas industries. Options for this liquid level indicator include metallic horn antennas or PP drop antennas for condensing atmospheres and corrosive media. pdf datasheet

Hycontrol non contact Radar level transmitter Radar RA Series 80 GHz for Hygienic Liquids

Radar RA Series 80 GHz for Hygienic Liquids

Hycontrol’s Reflex RA Series two-wire 80 GHz FMCW radar level transmitter is designed for hygienic liquids applications, where high precision is essential. It provides users in industries such as biochemical and food production with continuous, non-contact liquid level measurement. pdf datasheet

Hycontrol non contact Radar level transmitter RD Series 80 GHz for Powders & Dust

Radar RD Series 80 GHz for Powders & Dust

The RD Series two-wire 80 GHz FMCW radar level transmitter is designed for demanding applications with powders in very dusty atmospheres. With its small beam angle, this radar indicator is particularly suited for continuous, non-contact level measurement in high and narrow silos, hoppers or buffer storage containers up to 100 m/328 ft. Due to the high signal dynamics of the FMCW radar, the level transmitter is ideal for low-reflective media, dust, uneven surfaces or complex silo internal structures. As it features a flush-mounted PEEK lens antenna, there is no intrusion of the antenna into the silo, bin or hopper. It is ideal for dusty products such as cement, fly ash or GGBS. pdf datasheet

Hycontrol The RC Series is a two-wire 24 GHz FMCW non-contact radar level transmitter for solids

Radar RC Series 24 GHz for Solids

The RC Series is a two-wire 24 GHz FMCW radar level transmitter for basic applications with solid products. It provides continuous, non-contact level measurement of stones, granules, flakes and other such solid products for a variety of industries. It makes an ideal solid level indicator for large or high bins and silos. pdf datasheet

Novaris Surge Protector Hazardous Area Load Cell Protector IS-LCP

Hazardous Area Load Cell Protector IS-LCP

The IS-LCP provides protection for both 4-wire and 6-wire loadcells as well as the measuring instrument. The LCP is contained within an IP65 enclosure, or alternatively it may be supplied as an assembled PCB. As well as having IS certification the IS-LCP is engineered for installation into a loadcell circuit without affecting calibration.

Novaris Surge Protector Hazardous Area Threaded Signal Line Protectors IS-SLT

Hazardous Area Threaded Signal Line Protectors IS-SLT

The intrinsically safe and flameproof IS-SLT range provides surge protection for most twisted pair signal cables associated with intriscally safe field devices. Novaris ‘IS-SLT’ products are certified intrinsically safe and flameproof according to IEC Ex and ATEX and so may be installed in Ex d rated instruments without loss of integrity. The multistage design provides a high energy gas discharge tube (GDT) as primary protection for common mode disturbances, commonly associated with lightning strikes and power system earth faults and a secondary metal-oxide varistor clamping stage across the signal lines. This combination provides very robust surge protection with high transient suppression and low let-through voltages. In addition protection is provided for cable screens which may be open circuit at the instrument. Novaris ‘IS-’ products have been certified intrinsically safe according to IEC Ex and ATEX; the group IIC T4 certification makes it acceptable for use with all gas/air mixtures. With two different base options the SL protectors offer either direct earthing via Din rail, for the most effective, low impedance earth connection (-G base) or a connection via GDT to the DIN rail, offering isolation under normal conditions and equipotential bonding during a surge (-EC90 base). Novaris ‘IS-’ products are certified intrinsically safe according to IEC Ex and ATEX; the group IIC T4 certification makes it acceptable for use with all gas/air mixtures. With two different base options the SL protectors offer either direct earthing via DIN rail, for the most effective, low impedance earth connection (-G base) or a connection via GDT to the DIN rail, offering isolation under normal conditions and equipotential bonding during a surge (-EC90 base).

Novaris Surge Protector Instrumentation Hazardous Area Slimline Series Surge Protectors IS-SSP6A

Instrumentation Hazardous Area Slimline Series Surge Protectors IS-SSP6A

The IS-SSP6A intrinsically safe series surge protectors complement the IS-SL range for applications of load currents up to 6A. Typical applications may include power supplies, instrumentation and other low voltage requirements up to 6A. Novaris ‘IS-’ products have been certified intrinsically safe according to IEC Ex and ATEX; the group IIC T4 certification makes it acceptable for use with all gas/air mixtures. With two different base options the SL protectors offer either direct earthing via Din rail, for the most effective, low impedance earth connection (-G base) or a connection via GDT to the DIN rail, offering isolation under normal conditions and equipotential bonding during a surge (-EC90 base). Novaris ‘IS-’ products are certified intrinsically safe according to IEC Ex and ATEX; the group IIC T4 certification makes it acceptable for use with all gas/air mixtures. With two different base options the SL protectors offer either direct earthing via DIN rail, for the most effective, low impedance earth connection (-G base) or a connection via GDT to the DIN rail, offering isolation under normal conditions and equipotential bonding during a surge (-EC90 base).

Novaris Surge Protector Hazardous Area Slimline Signal Line Protectors  IS-SL

Hazardous Area Slimline Signal Line Protectors IS-SL

Novaris slimline surge protection devices (SPDs) provide surge protection for most twisted pair signaling schemes. Certified to be intrinsically safe Novaris IS SPDs can be installed in the hazardous zone or the field side of the IS barrier. This not only provides protection for the PLC or RTU I/O, it also provides protection for the IS barrier. Novaris ‘IS-’ products are certified intrinsically safe according to IEC Ex and ATEX; the group IIC T4 certification makes it acceptable for use with all gas/air mixtures. With two different base options the SL protectors offer either direct earthing via DIN rail, for the most effective, low impedance earth connection (-G base) or a connection via GDT to the DIN rail, offering isolation under normal conditions and equipotential bonding during a surge (-EC90 base).

Novaris Surge Protector DC Surge Diverter Low Voltage SDD2

DC Surge Diverter Low Voltage SDD2

Novaris SDD2 DC Surge Diverters offer an ideal solution for systems up to 150 Volts DC two phase systems. The SDD2 diverters are housed in a DIN compliant, fail-safe metal enclosure. Other voltages are available on request.

Novaris Surge Protector Spark Gap Surge Arresters SG

Spark Gap Surge Arresters SG

Use Spark Gap Surge Diverters for point of entry protection at main switchboards where direct strike protection is required. Carbon disk spark gaps are a robust and proven technology designed to handle long duration surges. The low resistance design minimises the energy dissipation within the device. Two models are available with either 50 kA or 110 kA of impulse current handling per phase for even the most extreme lightning environments. The Novaris spark gap diverters are a sealed unit and do not exhaust hot ionised gas into the switchboard.

Novaris Surge Protector Surge Protectors Series SSP

Surge Protectors Series SSP

Novaris SSP protectors are suitable for installation in circuits up to 63A. The SSP range has been engineered to provide excellent performance in an economical package. Protection is provided for all combinations of lines (L-N, L-PE, N-PE) ensuring the maximum level of protection is achieved at all times. Series surge protectors house the shunt (parallel) connection of the protection components internally within the device. This reduces the connection impedance to a minimum to guarantee optimal performance in all installations.

Novaris Surge Protector Two Phase Surge Filters for IT and DC power SFD2

Two Phase Surge Filters for IT and DC power SFD2

The Novaris SFD2 range of two phase surge filters are designed for protecting floating AC or DC power supplies. Applications include DC power supplies, balanced circuits for rail applications and single phase IT systems.

Novaris Surge Protector Spark Gap Filter SGF

Spark Gap Filter SGF

Novaris SGF surge filters provide optimum Class I MSB and DB protection using robust spark gap technology in combination with a low pass L-C filter for critical equipment up to 250A per phase.

Novaris Surge Protector Hybrid Surge Filter – 40 – 63 A HSF

Hybrid Surge Filter – 40 – 63 A HSF

The Novaris HSF is a hybrid surge filter with primary and secondary hybrid surge protection components plus a low pass filter. The hybrid design means the filter can continuously withstand phase to phase voltage between its phase and neutral terminals yet its performance equals that of other Novaris surge filters. This makes it ideal for applications where voltage regulation is poor and power line faults common.

Novaris Surge Protector Surge Filters 2A – 32A SFD

Surge Filters 2A – 32A SFD

Novaris SFD surge filters provide the highest level of protection for critical and essential equipment up to 32A per phase. Their compact design makes them an ideal choice for space restricted applications.

Novaris Surge Protector Surge Circuit Breakers SCB

Surge Circuit Breakers SCB

The Novaris Surge Circuit Breakers are designed specifically for short circuit protection of MOV based Type I and Type II (point of entry and secondary) shunt connected surge diverters. The SCB models have a continuous current rating of 3A to power the Novaris active alarm circuits but will not trip for large transient surges.

Novaris Surge Protector High Voltage Surge Diverters SDH

High Voltage Surge Diverters SDH

Novaris SDH High Voltage Surge Diverters have been engineered for system voltages above 600VRMS. Typical applications include aviation runway lighting, mining and railway industries.

Novaris Surge Protector Surge Diverters DIN SDD

Surge Diverters DIN SDD

Novaris SDD DINsafe Surge Diverters offer powerful performance at domestic MSB and industrial DBs. The SDD diverters are housed in DIN compliant, failsafe metal enclosures and are fully compliant to AS/NZS1768-2007 and to AS/NZ3000 wiring rules.

Novaris Surge Protector All Mode Surge Diverters SDN

All Mode Surge Diverters SDN

Use MULTIMOV all mode high energy surge diverters for point of entry protection at main switchboards, especially where N-PE protection is required. MULTIMOV surge diverters feature a parallel redundant arrangement of high energy metal oxide varistors (MOVs), thus promoting long life and exceptional surge handling capacity. In the event of a varistor failure the remaining segments continue to provide protection. The LED display indicates segment status and indicates normal operation when all LEDs are brightly lit.

Novaris Surge Protector MULTIMOV Surge Diverters SD

MULTIMOV Surge Diverters SD

Use SD – MULTIMOV high energy surge diverters for single phase point of entry protection at main switchboards. Models are available for all wiring systems worldwide. SD MULTIMOV surge diverters feature a parallel redundant arrangement of high energy metal oxide varistors (MOVs), thus promoting long life and exceptional surge handling capacity. In the event of a varistor failure the remaining segments continue to provide protection. A digital display confirms the device rating by displaying the percentage active of the redundant segments. The display indicates segment status and thermal overload. A failsafe alarm contact allows for remote monitoring.

Novaris Surge Protector C-Bus™ Protection Device  RJ45-1CB

C-Bus™ Protection Device RJ45-1CB

Novaris C-Bus™ RJ45 surge protection products are specifically designed for the protection of C-Bus™ RJ45 communications wiring. The Novaris C-Bus™ RJ45 network protector is designed with primary protection elements of the C-Bus™ network pairs and secondary protection elements to provide protection for the Remote Override pairs. The Novaris C-Bus™ protector contains integrated 230V isolation to prevent equipment damage during power to earth faults but also provide efficient earth bonding during a surge event.

Novaris Surge Protector RS-Serial Port Protectors

RS-Serial Port Protectors

Novaris DB Protectors provide protection for serial protocol systems in RS232 and RS485 applications. These units are housed in a headshell enclosure. The DB Protectors have a 90V earth isolation to prevent ground loops.

Novaris Surge Protector Multiline Protectors SLM

Multiline Protectors SLM

Novaris SLM offers protection for up to 12 signal lines. Each of the 12 lines have the protection referenced to ground making it an excellent choice for parallel signaling busses. Typical applications include process control, telemetry, PLC, and irrigation systems.

Novaris Surge Protector High Surge Current Signal Line Protector SLD

High Surge Current Signal Line Protector SLD

SLD Signal Line Protectors are designed to protect the most sensitive electronic equipment in lightning intense environments. So they are ideal for the protection of PLC’s, fire and security systems, railway signalling and SCADA equipment. Models feature multistage transient protection which delivers a greater level of protection through a staged approach. The primary stage absorbs the majority of the surge energy. The remaining stages provide accurate clamping and a degree of redundancy.

P1V1

Y Adapter for SLT

The SLT-Y offers a solution when a field instrument has no free cable entry to accommodate the SLT threaded instrument protector. The Novaris Y-piece adapter accommodates the SLT threaded instrument protector and cable gland. The SLT-Y is available in the same thread types as the threaded instrument protectors. The IS-SLT-Y-M20 is an IEC Ex and ATEX EX d certified version of the Y-Adapter, and so may be installed in Ex d rated instruments without loss of integrity.

SLT31

Threaded Signal Line Protectors SLT

Novaris threaded instrument protectors provide surge protection for instrumentation and are designed to be installed directly at the field equipment providing protection against induced surges and transients. They are suitable for two, three and four wire instruments. SLT models are available for signalling systems up to 200V. The multistage design provides a high energy gas discharge tube (GDT) as primary protection for common mode disturbances, commonly associated with lightning strikes and power system earth faults and a secondary metal-oxide varistor clamping stage across the signal lines. This combination provides very robust surge protection with high transient suppression and low let-through voltages. In addition protection is provided for cable screens which may be open circuit at the instrument.

SSP6A

Slimline Series Surge Protector SSP6A

The SSP6A series surge protectors complement the SL range for applications of load currents up to 6A. Typical applications may include power supplies, instrumentation and other low voltage requirements up to 6A. With two different base options the SSP6A protectors offer either direct earthing via DIN rail, for the most effective, low impedance earth connection (-G base) or a connection via GDT to the DIN rail, offering isolation under normal conditions and equipotential bonding during a surge (-EC90 base). The plug-in design provides simple and rapid replacement and testing – no rewiring needed. This also provides a convenient method of field equipment isolation if required.

sl2

Slimline Surge Protector SL2 / SLH2

The Novaris SL2 and SLH2 range provides 20kA high energy surge protection for balanced pair signaling circuits, used in a wide range of industrial monitoring and control equipment. Applications include SCADA, PLC, fire and security systems, telecommunications and railway signaling. The SL2 is designed for protecting communication circuits with a 3dB of 60Mhz and the SLH2 is designed for instrumentation power circuits requiring up to 2.5A of current.. The SL2 and SLH2 range integrates a fault indicator and external alarm connection for surge protection monitoring. They are available with a -EC90 option to isolate the earth connection for protection of field equipment. The protection and alarm circuit is contained in a replaceable cartridge to minimise downtime.

Novaris Surge Protector Slimline Signal Line Protectors SL

Slimline Signal Line Protectors SL

Novaris SL range of plug-in signal line protectors provide surge protection for most twisted pair signalling schemes. Ideal for the protection of PLCs, instrumentation, fire and security systems, telecommunications and telemetry systems, railway signalling, SCADA and other industrial monitoring and control equipment

Aplsens APIS Electropneumatic positioner

APIS Electropneumatic positioner

The APIS positioner is a final control element intended for control valves.It is intended for cooperation with pneumatic membrane and piston single and double-acting actuators with linear and rotational movement. It allows quick and precise controlling of displacement of actuator piston rod using analog or digital control signal.The positioner is controlled by a standard signal from two-wire 4..20 mA current loop or digitally in accordance with the HART 6 specification. It can be also equipped with a two-wire, current (4..20 mA) position transmitter of piston rod of the associated actuator. Current circuit of position transmitter is galvanically isolated from the input circuit of the control signal.The positioner can cooperate both with straight and reverse acting pneumatic actuators. The positioner can cooperate with single-acting actuators manufactured by Polna S.A., Samson, Arca Regler, Spiral-Sarco and double-acting actuators manufactured by Prema Kielce, Air Torque, Festo, Ebro Armaturen, El-0-Matic and by other manufacturers using proper mechanical coupling components. pdf datasheet

Influx Fire Sprinklersense Flow Switch and Test System from Influx
Influx Sprinklersense Flow Switch

Sprinklersense Flow Switch and Test Syste

The SprinklerSense flow switch and test system is an exacting solution for flow detection, monitoring and testing. A combination of cutting edge design and modern sensor technology helps to provide continuous assurance of flow switch operation and conditions inside sprinkler pipe-work. watch video

Influx Firesure LPC Fire Sprinkler

Firesure LPC Fire Sprinkler

Our Firesure flowmeters are designed for sprinkler fire pump testing. They are approved by LPCB and are simple and quick to install. We offer both our standard Firesure meter and our Firesure X meter, which allows for remote mounting, in a range of sizes suitable for both horizontal and vertical pipes and in a wide range of flows. They are both available with either flanged or grooved connections. These flowmeters are also available with FM approval. pdf datasheet

Influx Firesure FM Fire Sprinkler

Firesure FM Fire Sprinkler

Our Firesure FM flowmeters are designed for sprinkler fire pump testing. They have FM approval and are simple and quick to install. Firesure FM is available in a range of sizes suitable for both horizontal and vertical pipes and in a wide range of flows scaled in both USGPM and dm³/min. They are available with either between flange or groove connections. These flowmeters are also available with LPCB approval. pdf datasheet

firesureduog

Firesure Duo-Groove Fire Sprinkler FM & LPCB

Our Firesure Duo-Groove flowmeters feature a combined USGPM and L/min tube suitable for both LPC and FM approved installations. Key Features & Benefits Single combined l/min and USGPM tube. Suitable for LPC and FM installations. Stable easy to read flow indication. pdf datasheet

Influx Deltaflux high flow meter

Deltaflux high flow meter

The Deltaflux Orifice Meter is ideal for direct flow indication of high liquid or gas flows in large pipe sizes. It offers an economic, easy to use and low maintenance solution that does not require external powering. Key Features & Benefits High flows Direct reading Between flange connections Compact construction pdf datasheet

Influx Deltaflux high flow meter

iMT high flow meter

The iMT Metal Tube flowmeter features a high visibility, direct reading scale with options for remote switching or 4 to 20 mA output. It is well suited to high pressure, temperature and harsh environmental conditions. Key Features & Benefits 90° Linear Scale Easy to Read Repeatable & Stable pdf datasheet

Influx LPL high flow meter

LPL high flow meter

The LPL Series Housed Flowmeter is suitable for both our glass and acrylic flow tubes mounted within a rugged industrial housing. They are available in 3 tube scale lengths up to 250mm and various connection sizes. Key Features & Benefits Direct reading Low pressure drop High repeatability Rugged enclosure pdf datasheet

Influx Fluxline low flow meter

Fluxline low flow meter

Suitable for both our glass and acrylic flow tubes, Fluxline meters provide a safe and resistant solution for various applications. A high impact resistant polycarbonate cover surrounds the glass tube in our Safety Housed frame, protecting it from accidental damage. Flow tubes are also available separately for integration into customer equipment. Key Features & Benefits Low to medium flows Alarm options pdf datasheet

Influx Reflux low flow meter

Reflux low flow meter

Reflux Flow Transmitters combine variable area flowmeter and position sensing technology to provide both a direct reading and 4 to 20 mA transmission output in a single unit. This unique approach makes the Reflux Flowmeter an ideal choice for integration into customer equipment. Key Features & Benefits Low to medium flows 4 to 20 mA transmission Local indication pdf datasheet

Influx Uniflux low flow meter
Influx Uniflux low flow meter

Uniflux low flow meter

Uniflux direct reading flowmeters combine versatility, practicality and accuracy for the measurement of gas and liquid flowrates. They are available in standard, compact and long series as well as a range of materials and are suitable for panel or inline mounting. They offer either fine or ultrafine needle control valve options as well as high visibility and ease of installation. A wide range of standard and customised scales are available to meet even the most specific requirements Key Features & Benefits Alarm options High repeatability Interchangeable tubes. Low pressure drop pdf datasheet

Aplisens AT-2 Head-mounted smart temperature transmitter

AT-2 Head-mounted smart temperature transmitter

The temperature economical transmitter AT-2 is applicable to converting resistance of temperature sensor to standard current signal 4...20mA. pdf datasheet

efco TDFI Flange Facer with internal clamping
efco TDFI Portable lathes with internal clamping for machining flanges, flange facer for valves

TDFI Flange Facer with internal clamping

Due to its flat design and the low weight, the portable, ID-mounted TDFI facing machine with flanges is ideal for applications in areas with limited working space. The EFCO TDFI machine is particularly suitable for machining: Flanges of any kind Fitting housings Container flanges Heat exchangers Shipbuilding fittings Columns in refineries and the chemical industry Smooth and spirally grooved flange sealing surfaces

SPM-802

SPM Stationary Horizontal Lathe

Stationary precision turning machines, CNC-controlled. The optimum solution for complete machining of valves, for general overhaul and also for use in production. The machines of this range have precision inclined tables (±12°, accuracy ±10“) and have been optimised for more efficient machining of valves. A particular advantage for the machining of gate valve sealing faces is the clamping. It is possible to machine both sealing faces with only one clamping by adjusting the angle at the swivel table. The symmetry of both sealing faces is thus ensured. Due to the flexible design, SPM machines can also be used for other machining tasks. They are equipped with CNC programs that are specially tailored to turning requirements. During program development, special attention was paid to making operation as simple as possible. Operation takes place using a portable electronic control unit.

efco PDM Stationary Vertical Lathe

PDM Stationary Vertical Lathe

PDM machines are designed for the axial machining and facing of fitting housings (gate valves, valves, check valves), pumps and similar rotationally symmetrical components. They have infinitely variable speed control and axial and radial feeds (Z and X axis) with infinitely variable control that make it possible to move both axes simultaneously at different speeds. They are equipped with CNC programs that are specially tailored to turning requirements. During program development, special attention was paid to making operation as simple as possible. Operation takes place using a portable electronic control unit.

TDF NC CNC controlled Flange Facer efco portable lathe

TDF NC CNC controlled Flange Facer

The lathes in the NC series open up an almost infinite number of surface machining options. We achieve a completely new quality standard in flange and valve seat machining. Because of the pre-programmed processing cycles, the TDF NC special machine is ready for immediate use, and can be operated after just a small amount of instruction and no previous CNC programming knowledge. Machining options with the EFCO NC lathes. Of course, you can also supplement the program package with your own CNC programs.

efco TD NC CNC controlled Lathe

TD NC CNC controlled Lathe

With the portable CNC controlled lathes we achieve a completely new quality standard in flange and valve seat machining. Because of the pre-programmed processing cycles, the TD-2.02 NC special machine is ready for immediate use, and can be operated after just a small amount of instruction and no previous CNC programming knowledge. Machining options with the EFCO NC lathes. Of course, you can also supplement the program package with your own CNC programs.

efco Portable lathes for cutting out welded seat rings in valves (ASM)

ASM Portable lathes for cutting out welded seat rings in valves

The ASM is a portable lathe for cutting out welded seat rings in valves. It is suitable for use on site and in the workshop, in nuclear power plants, in conventional power plants, for valve service, for the chemical and petrochemical industry, in steel construction in shipyards and oil fields.

efco TDF Flange Facer with external clamping

TDF Flange Facer with external clamping

When seals are replaced, it is frequently unavoidable that the sealing faces themselves have to be remachined due to damage from heat or aggressive media. Our portable flange facing machines with external clamping are suitable for this type of work in pipelines, on large valves, pumps, chemical plant, turbine housings, heat exchangers etc. Simple installation, low weight and flat design of the machines make use of these machines possible on site in almost any position. The required roughness of the sealing faces can be obtained due to variable feeds during machining. Inclined faces can be machined using additional tools.

efco TD Portable lathes for sealing faces, flanges and bores in valves

TD Portable lathes for sealing faces, flanges and bores

The EFCO TDs are portable lathes for precision machining of bores and sealing surfaces in valves, cylinders, pumps, turbine housings, etc. These machines are suitable for use on site and in the workshop, in power stations, for valve servicing, for chemical and petrochemical facilities, in steel construction, in shipyards and in oilfields. pdf datasheet

efco Rotago Ball Valve Lapping Machine

Rotago Ball Valve Lapping Machine

Stationary ball valve lapping machine for the simultaneous finishing of the ball and 2 metallic sealing rings. For small and medium-sized ball workpieces with diameters of up to 300 mm.

efco SM Stationary Grinding & Lapping Machine- Safety/Gate/Non-return Valves, Gates

SM Stationary Grinding & Lapping Machine- Safety/Gate/Non-return Valves, Gates

Stationary grinding and lapping machines for the repair of sealing faces in valves and gates. These machines are characterized in particular by their stable and robust design, compact machine concept, very high table load and modular concept. A second table can be retrofitted at any time. Driven planetary gears to increase removal can also be retrofitted.

efco FLM Stationary Surface Lapping Machine

FLM Stationary Surface Lapping Machine

EFCO surface lapping machines are excellent for lapping individual or series components, face seals, valve seats, gates, etc.. Worn components, such as valve seats, mechanical shaft seals, disks, etc., can be re-lapped in repair workshops and at refurbishment companies. Automatic and finely adjustable lapping compound feed as well as freely adjustable lapping table speed guarantee high quality lapping results.

efco KS Stationary Grinding Bench

KS Stationary Grinding Bench

The KS stationary grinding machines for valve and machine components can be used on site or in the workshop. They are suitable for face grinding gates, valve seats and other machine components. The aluminum grinding plate is fitted with self-adhesive abrasive disks. A fixed stop provides improved guiding of the work piece. pdf datasheet

efco TSV Excentrical Grinding and Lapping machine
efco VSA High-speed grinding machine for machining flat and conical seats in valves and on flanges

VSA High Speed Precision Grinding

Portable high-speed grinding machine for machining flat and conical sealing faces in valves and on flanges. Particularly suitable for precise grinding of heavily damaged faces, cylindrical holes and conical sealing faces, in particular after build-up welding pdf datasheet

efco TSV Excentrical Grinding and Lapping machine for safety valves

TSV Excentrical Grinding and Lapping

Grinding and lapping machines for safety valves (TSV) The EFCO TSV is a portable grinding and lapping machine with excenter for the machining of sealing faces of safety valves. pdf datasheet The machine has two separate drives. This results in a cross-ground and absolutely flat sealing face.

efco SLA Sealing Faces for retrofitting

SLA Sealing Faces for retrofitting

Portable machines for grinding and lapping of sealing faces in gate valves and non-return valves, gates and flanges. Optionally, these machines can be fitted with a digital rocker for contact pressure. This patented unit guarantees reproducibility and absolutely flat sealing faces. In addition, our valve grinding machines can be fitted with a swing-check adapter to enable machining of sealing faces on non-return valves with a large inclination. Hard seats can be machined with our portable high-speed valve grinding machine with driven spindles. This makes extremely fast and effective machining possible. This option can be retrofitted (SLA) on existing machines or can be supplied as a complete system. Fast setup and removal of the machines is guaranteed by means of a specially developed clamping block. pdf datasheet

efco HSL Portable machines for grinding and lapping of sealing faces in gate valves and non-return valves, gates and flanges.
efco HSL Portable machines for grinding and lapping of sealing faces in gate valves and non-return valves, gates and flanges.

HSL Sealing Faces

Portable machines for grinding and lapping of sealing faces in gate valves and non-return valves, gates and flanges. Optionally, these machines can be fitted with a digital rocker for contact pressure. This patented unit guarantees reproducibility and absolutely flat sealing faces. In addition, our valve grinding machines can be fitted with a swing-check adapter to enable machining of sealing faces on non-return valves with a large inclination. Hard seats can be machined with our portable high-speed valve grinding machine with driven spindles. This makes extremely fast and effective machining possible. This option can be retrofitted (SLA) on existing machines or can be supplied as a complete system. Fast setup and removal of the machines is guaranteed by means of a specially developed clamping block. pdf datasheet

efco Portable machines for grinding and lapping of sealing faces in gate valves and non-return valves, gates and flanges.

SL Sealing Faces

Portable machines for grinding and lapping of sealing faces in gate valves and non-return valves, gates and flanges. Optionally, these machines can be fitted with a digital rocker for contact pressure. This patented unit guarantees reproducibility and absolutely flat sealing faces. In addition, our valve grinding machines can be fitted with a swing-check adapter to enable machining of sealing faces on non-return valves with a large inclination. Hard seats can be machined with our portable high-speed valve grinding machine with driven spindles. This makes extremely fast and effective machining possible. This option can be retrofitted (SLA) on existing machines or can be supplied as a complete system. Fast setup and removal of the machines is guaranteed by means of a specially developed clamping block. pdf datasheet

LS pipe ends with lenticular gaskets efco grinding machine

LS pipe ends with lenticular gaskets

Portable machines with special tools for the grinding of pipe ends with metallic 140° lenticular gaskets (to BASF and DIN 2696). Fast and simple centring of the tools guarantees effective and high quality repair results. pdf datasheet

EFCO VSK conical valve seat portable machine for lapping and grinding
efco VSK conical seat portable machine for lapping and grinding

VSK conical seats

Portable machines with special tools for the grinding of conical sealing faces in high-pressure, shut-off and control valves. Fast and simple centering of the tools guarantees effective and high quality repair results. pdf datasheet watch video

efco Valva flat seat portable machine for lapping and grinding
efco Valva flat seat portable machine for lapping and grinding

Valva flat seats

Portable machines for grinding and lapping of sealing faces in valves, valve disks, flanges etc. in flat seats, Work range: DN 8 – 1600 mm (¼“– 64“) pdf datasheet watch video

efco High Pressure Compressor Booster

High Pressure Compressor Booster

For the generation of high pressure or the compression of air or nitrogen and storage in the integrated pressurised bottle at up to 350 bar (approx. 5075 psi).

efco Automatic Test Benches PS-A

Automatic Test Benches PS-A

Test bench with automatic test sequence for testing shut-off valves PS-7,5A / 15A - DN15 (1/2“) - DN250 (10“) pdf Testbench

efco  Horizontal Test Benches PS-H 200-600T
efco  Horizontal Test Benches PS-H 200-600T

Horizontal Test Benches PS-H 200-600T

The horizontal test bench EFCO PS-H M series in modular design with a clamping force of 200 - 600 t for testing shut-off and control valves. Water examinations are possible in combination with air or nitrogen. pdf Testbench

efco Vertical Test Benches PS-15 / 30 / 50 / 75

Vertical Test Benches PS-15 / 30 / 50 / 75

Valve test bench for testing of safety valves and shut-off / control valves DN 15 (1/2“) - DN 500 (20“) Proven technology standardised and in modular design. Cost-effective and short delivery time. Basic program with variants and many options. pdf Testbench

efco Vertical Test Benches for Safety Valves PS-SV15 / 30 / 50

Vertical Test Benches for Safety Valves PS-SV15 / 30 / 50

Valve test bench for testing safety valves DN 15 (1/2“) - DN 400 (16“) pdf Testbench

The EFCO portable PS-T 10 vertical test valve bench is suitable for testing shut-off valves and safety valves.
ps_t10.03

Portable Test Bench PS-T10

The portable PS-T 10 is suitable for testing shut-off valves and safety valves. The test specimens are clamped vertically and can be optimally vented by filling from below. pdf Testbench

Page 1 of 2